This paper addresses the issues related to designing and estimating the strength of solid-alloy elements in the deforming broaches of significant diameter (exceeding 150 mm) for the developed process of discrete broaching. The tool limit condition was assessed based on two strength criteria: the specific potential energy of shape change and the maximum tangent stresses. Numerical modeling using the finite element method has made it possible to derive the distribution of equivalent stresses in the tool elements and the contact stresses (...) at the surface of the contact between a solid-alloy insert and the body, which enabled the analysis of tool strength under loading. The simulation was performed under a single normal load, which ensured the versatility of the calculation for any contact pressure values. We have derived formulae to calculate the acceptable contact pressure depending on unit load. The effect of the insert protrusion height over the body on the strength of tool elements has been established. We have derived engineering dependences that determine the required magnitude of insert protrusion over the body depending on the ultimate load. An example of calculating the strength of a prefabricated deforming element in the machining of a sleeve made from gray modified cast iron of hardness HB230 has been considered. Our calculations have shown that the deforming element designed for the new technological process corresponds to the conditions of strength, provided the ratio h1/h=0.15 is maintained (where h1 is the insert height above the body, h is the insert height). The results obtained could be used in engineering calculations when designing the prefabricated tool for discrete deformation, as well as to assess the strength of prefabricated tools, such as cutters, core drills, reamers, when refining external loads. (shrink)

Purpose. To determine the potential of deforming broaching for the improvement of efficiency of cutter chisels in the mining industry. Methodology. The study of the application of the technological process of deforming broaching was carried out based on the experimental research into conditions of assembly of press couplings corresponding to cutting rock-destroying tools, the working surface of which is reinforced with solid-alloy inserts. Findings. Based on the conducted research, a new process of assembling the crowns of cutter chisels with the (...) use of deforming broaching was developed. Originality. It was determined that the range of angles of inclination of generatrix of the working cone of the deforming element and the roll-treading lip of the insert, which are necessary for efficient machining and pressing in crowns of cutters, is 4–16°. It was proven that the “solid alloy-steel” press couplings for cutter chisels will have the maximum bearing capacity at total tension a/d0 ≤ 3 %. It was found that it is necessary to foresee the following distribution of tensions: to perform 2 % of deformation by preliminary deforming broaching, and 1 % ‒ by pressing in an insert Practical value. The use of deforming broaching makes it possible to increase the strength of fastening the inserts of cutter chisels by 2 times, to reduce specific consumption of the tool by 4.4 times, and to increase the average drilling rate by 4 times. (shrink)

jild-i 1. Chand maqālah darbārah-ʼi maqāmāt-i [i.e. maqālāt] ʻilmī, va mujāhadāt-i farhangī, va khadamāt-i Islāmī-i ū-- -- jild-i 2. Chand maqālah az Prūfisūr ʻAbd al-Javād Falāṭūrī Iṣfahānī.

R.I.G. Hughes presents a series of eight philosophical essays on the theoretical practices of physics. The first two essays examine these practices as they appear in physicists' treatises (e.g. Newton's Principia and Opticks ) and journal articles (by Einstein, Bohm and Pines, Aharonov and Bohm). By treating these publications as texts, Hughes casts the philosopher of science in the role of critic. This premise guides the following 6 essays which deal with various concerns of philosophy of physics such as laws, (...) disunities, models and representation, computer simulation, explanation, and the discourse of physics. (shrink)

James I. The Political Works of James I. Reprinted from the Edition of 1616. With an Introduction by Charles Howard McIlwain. Cambridge: Harvard University Press, 1918. cxi, 354 pp. Reprinted 2002 by The Lawbook Exchange, Ltd.